X-Bridge - Smoke-Systems

Go to content

X-Bridge

Telemetry-EL
Telemetry for the Spektrum X-BUS

The X-Bridge translates Jeti-telemetry data into Spektrum's X-Bus protocol. The sensor is simply plugged into the JR connection of the X-Bridge. There are two sockets for the X-Bus so that additional X-Bus sensors can be connected.

You choose the X-Bridge that suits your sensor.
We have already done the configuration for you.
plug and play



Supported sensors
The following sensors are currently supported by the X-Bridge:

JetCat ECU
  • Version 10 with Telemetrie-Adapter
  • Version 12
  • Pro Interface
Jeti MEZON esc
  • with or without BEC
YGE esc
  • with or without BEC
Smoke-EL
  • SmokeDriver ab HV
JetCAT ECU
The AirWare in the transmitter determines what data can be displayed and how that data is displayed. Therefore the X-Bridge is available in two versions. The NX version supports all Spektrum NX series transmitters, the DX-IX version works with the AirWare DX and IX series. AirWare determines which alarms are possible, the X-Bridge cannot influence this.
NX series transmitters
This transmitter only supports the ECU data to a limited extent. Therefore the X-Bridge creates a text screen for displaying the ECU data. This is not optimal, as the refresh time for the display is 0.6 seconds and alarms are not possible. However, so that you still receive alarms, the X-Bridge also uses the data area of Smoke-EL. Here you can set an alarm for the ECU battery and for a malfunction (CutOff). So you always have your turbine in view with an NX transmitter.
DX and IX series transmitters
These transmitters support the ECU data directly with their own data structure. But here, too, there are differences in how the data is displayed and in the alarms. You set the alarms as usual in the telemetry setting of your transmitter. The X-Bridge delivers the data from the ECU to the transmitter, and further processing is then exclusively handled by the transmitter's AirWare.



-
Jeti MEZON ESC
Here, too, AirWare determines how the data is displayed, the X-Bridge receives the data from the controller and forwards it to the X-Bus.
The representation of the data
The X-Bridge transfers the MEZON data to two sensors on the Spektrum X-Bus. The data is displayed as ESC and flight battery in the transmitter. MEZON controllers can be used with or without BEC. If BEC data are available, they are displayed accordingly. The power and BEC temperature values are not displayed.
The display for the flight battery shows the motor current and the battery capacity that has already been used.

Alerts:
The spectrum airware offers a variety of alarms. Please set the notifications in the way that suits you best. The X-Bridge does not generate any alarm messages.


-
YGE ESC
Here, too, AirWare determines how the data is displayed, the X-Bridge receives the data from the controller and forwards it to the X-Bus.
The representation of the data
The X-Bridge transfers the YGE data to two sensors on the Spektrum X-Bus. The data is displayed as ESC and flight battery in the transmitter. YGE controllers can be used with or without BEC. If BEC data are available, they are displayed accordingly. The power value are not displayed. The display for the flight battery shows the motor current and the battery capacity that has already been used.

Alerts:
The spectrum airware offers a variety of alarms. Please set the notifications in the way that suits you best. The X-Bridge does not generate any alarm messages.


-
No matter what type of serder you use, with the X-Bridge you always have an eye on the telemetry data.

Technical specifications:
Dimension..............              35 x 12 x 8 mm
Voltage...................               5 – 12 Volt
Weight....................              6g
Current......…......….             max. 30mA
Interfaces....……….             2  X-Bus, 1 JetCat/Smoke-EL
X-Bridge
The X-Bridge provides Jeti-telemetry data for the Spektrum XBus.
These telemetry sensors are currently supported:

• JetCat ECU ab V10
• Jeti-MEZON esc
• YGE esc
• SmokeDriver from Smoke-EL

Supplied with an XBus patch cable.


Please select the sensor you like to use:
69,00€(MwSt. incl.)
Add
kostenloser Unofficial WsX5 Counter!
Back to content